Have you come to a point your Milwaukee hammer drill isn’t working as usual? Moreover, this may not be the case with you. Yours may be on the contrary; learning about the format of repairing Milwaukee hammer drills may be your passion as a developing hobbyist. Whatever the situation, this will aid.
Definitely, every power tool encounters technical faults. And one of the most vulnerable parts that need immense attention is the chuck. It doesn’t hurt if your Milwaukee hammer drill chuck becomes faulty, but it hurts if you don’t learn how to troubleshoot when the Milwaukee hammer drill chuck stuck.
The default could either be minor or severe, but when you know how to troubleshoot such mishaps, you’ll be able to save some bucks and use your Milwaukee hammer drills dependably.
First, acknowledge that the bit ought to enter through the keyed and keyless chucks through the chuck. And, the Milwaukee hammer drill chucks’ jaws have to grip the bits’ sleeves cordially.
SDS MAX hammer drill bits have the standard size for Milwaukee hammer drills. Of course, the bits with the correct size should be used on your unit’s chuck. Once you use the valid bit, but if you suddenly can’t remove the drill bits, read the steps below to remove the bit safely.
How Do You Remove a Chuck from a Milwaukee Hammer Drill?
1. Conventional Steps of Removing Milwaukee Hammer Drills
- Switch off the unit’s power before you start removing the bit from your Milwaukee hammer drill.
- Grip the chuck and twist it in a backward direction to release the jaws that hold the sleeves of the bits. Do this gently to avoid unnecessary mishaps.
- Allow the jaws to open widely before you wiggle out the bit from the hook. Use your fingertips to twist the bits from the hook until they are released.
- Provided you’re using an adapter; then you’d seriously have to remove the adapter through the conventional method before you remove the bit.
- The clinking of the jaws occurs during the removal of the bits, so that’s not a problem.
2. Using Allen Keys
This is viable when the bit is stuck on the inside of the chuck in a keyed chuck. The Allen key could be preordered from Milwaukee, or any available one of compatible size could be used.
What it does is that it’s used for releasing the chuck plastic cover each time it’s stuck. It’s often turned to the left after it grips the chuck firmly to make the release of the close jaws perfect. The Allen keys could be used the same way a wrench would release a keyless chuck, but it has to be in place first.
The key has to be struck with a hammer to enhance the twisting of the chuck counterclockwise for the jaws to open.
3. Screwdriver
There are screws that enable the chuck to stay in place. Use the instruction in the manual to identify the portion on the chuck where the screws could be removed.
The removal of the screws would ease the release of the jaws. In addition, provided the bit is right for the chuck size but the jaws aren’t coherently gripping the sleeve of the bit, this could affect the rotation of the bit.
Therefore, you’re to check this and correct it. Dirt is another factor that could affect the bit’s revving power; all these could only be corrected by screwing out the chuck and cleaning the chuck when jammed.
4. Other Corrective Measures
Ensure the bit firmly clings to the hook without wobbling before using it. Firstly, this would prevent the bits from loosely coming out intermittently from their place. The incompatibility of a bit for the chuck’s size could cause the jamming of the bit.
In a scenario that you find the motor is rotating at the rear, but the chuck isn’t propelling the bit, then this implies the chuck needs to be replaced. Notwithstanding, reading the manual and learning how to use the Milwaukee hammer drill’s model will enable one to operate the unit discreetly.
Finally, greasing the chuck and the bits will elongate the use of the Milwaukee hammer drill chuck, mainly if one uses the bit for the first time.
Milwaukee M18 Drill Chuck Problems:
The familiar challenge operators encounter with using Milwaukee m18 is the loose chuck. Nominal buyers have complained about its difficulty drilling multiple workpieces at a time. However, this could be relieved by using the right bit that suits the chuck and lightly on workpieces. Better still, you can contact the manufacturer on the chuck replacement if the need for the model is quite needful.
Milwaukee Drill Chuck Screw Size:
This depends on the model of the unit. The size of the screw recommended is equivalent to the bit size that’s advisable for the chuck installed on the unit. However, Milwaukee drill chucks use screws between 1.5mm and 13mm. You can find out the specifications by reading the manual that comes with the product or calling the unit’s manufacturer.
Milwaukee Hammer Drill Chuck Replacement:
Milwaukee hammer drills could have their chuck replaced when needed. Operators are to call the manufacturer or visit a nearby store and inform them of the type of Milwaukee hammer drill chuck needed. It could be keyed and keyless. After this has been stated and other specifications, one can buy a new replacement. Nevertheless, unscrew the chuck and remove it before you replace it.
Final Words
This is how you can remove bits from Milwaukee hammer drills when stuck. This is the safest way of troubleshooting the technical faults in the chuck without damaging it. You can depend on every information expressed here for other brands and Milwaukee models. Nevertheless, this article has also stated instances that would enable you to prevent the mishap in the first place.